If you\u2019ve got some old scrap wood lying around, why not use it to make your very own DIY wood cutting board. Not only is the project cheap and easy to finish, but it\u2019s also a great gift for pretty much anyone old enough to use a knife.\n
\n
First things first, you have to decide on the type of wood you want to use. The one we\u2019re using in this guide is walnut. You can also use maple, cherry, or any other hardwood that has a tight grain pattern.\n
\n
Start by taking a piece of walnut and chopping it up using your miter saw. Go for a measurement of about 15-16 inches.\n
Once you\u2019ve chopped your wood up, clean each of the edges with your jointer jig at your table saw.\n
\n
With an edge on every board cleaned up, take that edge and reference it against your table saw\u2019s fence before cutting them into strips. The width of every strip should represent the cutting board\u2019s overall height when the wood cutting board is done.\n
This time, go for a measurement of about an inch and three quarters. This should be enough since you\u2019ll remove some of that thickness when you take it to the planer later on.\n
\n
You might notice some gaps between the pieces which you\u2019ll want to take care of as early as now. Forcing them together with glue and clamps might give you issues down the road.\n
Take out your jointer and run them all through. Afterward, use your planer and run them through again. They should now be nice and flat \u2013 ready to be glued up together.\n
\n
Clamp the cut pieces together just tight enough to squeeze out the glue from the top and bottom. Clean the glue off of the wood and leave it to dry for a couple of hours.\n
Tip: When clamping, make sure to put equal clamping pressure all the way through. To do this, put two clamps on the top and two more on the bottom. Avoid overtightening as this may lead to warping in your board later on.\n
\n
With the glue now dry, put your wood cutting board through your planer again. Afterward, take it to your table saw and clean the edges up using your crosscut jig.\n
For that personal touch, you can add an engraving to your wood cutting board at this point. Once that\u2019s done, you can also add a chamfer along all of its sides to remove any of those sharp edges.\n
\n
Start off at 120 grit and slowly work your way up to 220 grit.\n
Once you\u2019re done with your first round of sanding, spray the entire thing down with water to raise the little fibers up and ready it for another round of sanding. Let it dry completely before you sand it again up to 220 grit the next time.\n
Remember: Sand, spray down, and sand again. Also, don\u2019t forget to use a protective mask.\n
\n
Use mineral oil and season your new board with at least three to four coats. In other words, just put a coat on, wait for about 20-30 minutes, wipe the excess off, rinse, and repeat.\n
You can finish things off using another conditioner that has both mineral oil and some waxes. Keep a bottle of this conditioner handy.\n
A wood cutting board tends to dry up over time. As soon as you start seeing that, just put a coat of the conditioner on and it should rejuvenate the thing.\n
The final product should look like this:\n
\n","protected":false},"excerpt":{"rendered":"
If you\u2019ve got some old scrap wood lying around, why not use it to make your very own DIY wood cutting board. Not only is the project cheap and easy to finish, but it\u2019s also a great gift for pretty much anyone old enough to use a knife. What you’ll need: Hardwood (we used walnut\n","protected":false},"author":1,"featured_media":11588,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"_seopress_robots_primary_cat":"","_seopress_titles_title":"","_seopress_titles_desc":"If you\u2019ve got some old scrap wood lying around, why not use it to make your very own DIY wood cutting board. Not only is the project cheap and easy to finish, but it\u2019s also a great gift for pretty much anyone old enough to use a knife.","_seopress_robots_index":"","_jetpack_memberships_contains_paid_content":false,"footnotes":""},"categories":[21],"tags":[100,96,30,122,46],"class_list":{"0":"post-11587","1":"post","2":"type-post","3":"status-publish","4":"format-standard","5":"has-post-thumbnail","7":"category-tie-life-style","8":"tag-diy","9":"tag-diy-home","10":"tag-household-hacks","11":"tag-kitchen-hacks","12":"tag-life-hacks"},"jetpack_featured_media_url":"https:\/\/inovatestory.com\/wp-content\/uploads\/2021\/07\/diy-wood-cutting-board.png","jetpack_sharing_enabled":true,"_links":{"self":[{"href":"https:\/\/inovatestory.com\/wp-json\/wp\/v2\/posts\/11587","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/inovatestory.com\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/inovatestory.com\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/inovatestory.com\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/inovatestory.com\/wp-json\/wp\/v2\/comments?post=11587"}],"version-history":[{"count":0,"href":"https:\/\/inovatestory.com\/wp-json\/wp\/v2\/posts\/11587\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/inovatestory.com\/wp-json\/wp\/v2\/media\/11588"}],"wp:attachment":[{"href":"https:\/\/inovatestory.com\/wp-json\/wp\/v2\/media?parent=11587"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/inovatestory.com\/wp-json\/wp\/v2\/categories?post=11587"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/inovatestory.com\/wp-json\/wp\/v2\/tags?post=11587"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}